Where to find inflatable breasts?

[TheWolverine1]

Hello All!

Interesting question. I finally got the nerve to bring this whole fetish thing up to my fiance and much to my surprise, she's into BE too 0_0

That said, we've been trying to hunt down inflatable breasts to create a role-play scenario. Considering she's naturally an H cup it might be a little tricky, but so far we haven't been able to find anything period.

Has anyone come across anything or can point me in the right direction on where I can find the parts to build an apparatus?

Thank you!

[fredzor]

Most of the props you see in videos are custom built. There's plenty of low-tech stuff you can do with an air compressor.

[foxmaster5]

Shes an H cup and you want to make her bigger? Tell her to wear a reducing bra and then when she takes it off shell look bigger.

[TheWolverine1]

Originally Posted by foxmaster5

Shes an H cup and you want to make her bigger? Tell her to wear a reducing bra and then when she takes it off shell look bigger.

A lot of this is her idea actually. She's hoping we can come up with something not only for us, but that we might be able to contribute to the community.

Thanks for your input guys!

[Naonao]

Yeah, most of the props are custom made.
There are silicone prosthetics/inserts but they are extremely expensive. I would say: Double-layer a balloon and experiment with various fillers! Much cheaper and fairly durable.

In any case, you'd have to keep in mind that expanding whatever the prop is via a pump can and will eventually wear it out, just like anything really!

[jerrycurly]

Also looking for this. We've tried extra large silicon pads, the three cup size ones, which I found on eBay, but she's also an h cup and they don't work, their just not the right shape. What's double layer a balloon? I think just various sizes would be good, inflatable would be a bonus.

[Naonao]

Originally Posted by jerrycurly

Also looking for this. We've tried extra large silicon pads, the three cup size ones, which I found on eBay, but she's also an h cup and they don't work, their just not the right shape. What's double layer a balloon? I think just various sizes would be good, inflatable would be a bonus.

Normal balloons! You can also get specialty ones that are very large.
You simply insert one same-sized balloon into another one.
The reason you wanna do this is because it makes them very very durable and remain very round. Single-layering can be fragile, but much easier to inflate.

Also don't use expensive clothes since they'll get ruined/stretched out quickly.

[NimrodClover]

A few months back Bambi Blaze was selling most if not all of her BE props.
I have no idea if they are still available. If you have a BEA membership there is a link here: http://forum.bearchive.com/index.php...ml#msg10225554

She has been a long time BE contributor and her departure from the role is sort of the end of an era.



Ah, the good old days...

[Scorch]

Originally Posted by NimrodClover

A few months back Bambi Blaze was selling most if not all of her BE props.
I have no idea if they are still available. If you have a BEA membership there is a link here: http://forum.bearchive.com/index.php...ml#msg10225554

She has been a long time BE contributor and her departure from the role is sort of the end of an era.



Ah, the good old days...

She's left? She did make some good stuff, sure,I hated her as a person for my own reasons, but she did some good content.

[Kevin_Generic]

Originally Posted by NimrodClover

A few months back Bambi Blaze was selling most if not all of her BE props.
I have no idea if they are still available. If you have a BEA membership there is a link here: http://forum.bearchive.com/index.php...ml#msg10225554

She has been a long time BE contributor and her departure from the role is sort of the end of an era.



Ah, the good old days...

Does anyone know exactly who created the inflatable props Bambi used in her videos?

[AirWolf]

First off, I am sorry to bump an old thread. I have been away from the community for a rather long time. Hopefully the info I post in this thread will make the bump worth while for some folks!

Originally Posted by Kevin_Generic

Does anyone know exactly who created the inflatable props Bambi used in her videos?

I happen to know the fellow who did that work.
Me.

While I am not currently in a position to make anything similar to those particular props, I have recently been toying with new designs, fabrication methods, and materials.

It is important to point out, those props and the "film quality" ones I may be making in the future are labor-intensive. (the normal (non-lactating) boob prop took something in the range of 45-50 hours of labor to create) So they were expensive.

However, like I said I have been looking into new ideas which offer "low budget" alternatives, but still retains good visual qualities.

That being said, I would be happy to field any question for folks on a very tight budget who want to use common materials like balloons, but want it to be as realistic as possible.

Simple tips:

1, Equal Inflation; When trying to inflate 2 balloons at once, it is best to have 2 separate air pumps that can be regulated OR if you are using compressed air, a "T" connection attached to 2 regulators with each going to one of the props. This allows for independent control of the props since latex props tend to inflate unequally.

2, One-Way Valves; It is also handy to have simple 1 way valves to keep each prop inflated after the expansion. These are inexpensive to purchase. Look for them in any aquarium section of a store. They should be connected as close to the prop as possible to allow for mobility of the person wearing the prop.

3, Flesh Coloring; Probably the most difficult thing to do is finding a balloon that come close to actual flesh colors. Latex body paint can come in a variety of flesh colors, but to make it match even better, get some acrylic paint in the following colors; dark brown, red, and, white. Depending on the tone of skin to be matched, of course.
This can be a tedious process of adding a small amount of paint to the latex body paint, putting a drop on some paper or cardboard and waiting for it to dry. so you can match the dried color to the skin you are trying to match.
You would then have to clean the outer surface of the balloon. I suggest using carburetor cleaner from any automotive section(it needs to be a hydrocarbon for this part) Take the balloons outside, spray them down and rub them off with a clean paper towel.(try not to get any inside the balloon) Then let them air dry.
You can then dip or paint the coloring onto the balloon. The balloon needs to be slightly inflated.(just enough to make it "plump" but not so much that it begins to stretch) Dip or paint the coloring on and then let it dry while slightly inflated. (you can fill the balloon with hot water, use a hair dryer, or even heat lamp to accelerate the drying speed) It will likely take many coats of paint (5+) to fully hide the original balloon color especially if the balloon is an odd or dark color and you are trying for a light color skin tone. Note the original balloon color may show though when inflated if you don't have enough coats of paint on it.
When the final coat of paint is dry, coat the exterior in talcum powder (baby powder) to keep it from sticking to it's self, and let it sit a warm dry place for at least 3 days. (This allows the rubber to cure fully.) Alternatively, you can vulcanize it in a oven set to 175-degrees Fahrenheit for about 1 hour. (just use plain water to remove the talcum powder when you are ready to use the prop)

4, Liberal Use Of Talcum Powder; When it comes to latex, you really can't use too much talcum powder. If you are putting one balloon inside another, put extra talc in the outer balloon. This keeps the latex from the inner and outer balloons from rupturing due to friction between the two. Any time latex is touching the skin during an inflation, it is also a good idea to use talc on the skin to avoid "friction burns".

That's about all I can think of off the top of my head.

Happy inflating folks!

[foxmaster5]

Well I can point you here. They made a great rig, some good youtube videos from it as well. But the man never told anyone how he did and has since disappeared off the face of the earth. Sorry I cant really provide much more

http://thesweaterpupbreeder.deviantart.com/